Loading branch status…
Home / Waterproofing & Sealants / Bitumax APP Waterproofing Membrane 4.5 kg Mineral – 1m x 10m (45 kg Roll)
Bitumax APP Waterproofing Membrane 4.5 kg Mineral – 1m x 10m (45 kg Roll)

Bitumax APP Waterproofing Membrane 4.5 kg Mineral – 1m x 10m (45 kg Roll)

KSH 5,000/ piece
In stock
About this product

Insutech Bitumax APP Waterproofing Membrane 4.5 kg Mineral – 1m x 10m (45 kg Roll)

Heavy-duty, mineral-surfaced torch-on roofing membrane for flat concrete roofs, terraces and balconies. In stock at Shabbiri Hardware, Magadi Road – Ongata Rongai and Tuala, Nairobi.

APP Modified Bitumen 4.5 kg/m² 1m x 10m Roll Mineral Surface Torch-On

Product Overview

Bitumax APP membrane by Insutech is a 4.5 kg/m² APP (Atactic Polypropylene) modified bitumen waterproofing membrane with a mineral granule top surface. It is torched onto a primed surface to form a continuous, seamless waterproof layer that keeps rain, ponding water and moisture out of your slab.

The mineral finish shields the bitumen from strong Kenyan sun and UV, so Bitumax can be left exposed as the final roofing layer on flat roofs, terraces and parapets. Each roll measures 1 metre wide by 10 metres long (10 m²) and weighs about 45 kg.

Whether you are a contractor waterproofing a new apartment roof in Rongai, Kitengela or Karen, or a homeowner fixing a leaking slab, Bitumax gives you a dependable torch-on membrane at your nearest Shabbiri Hardware branch.

Technical Specifications

PropertyDetail
Brand / ProductInsutech – Bitumax
Membrane typeAPP (Atactic Polypropylene) modified bitumen, plastomeric
Mass per unit area4.5 kg/m²
Roll width1.0 m
Roll length10.0 m
Gross area per roll10 m²
Approx. roll weight45 kg
Top surfaceMineral granules (UV protective, can be left exposed)
Method of applicationTorch-applied (propane gas torch)
Recommended primerBitumen primer (solvent-based)
Recommended side lap100 mm minimum
Recommended end lap150 mm minimum, staggered
Effective coverage per rollApprox. 8.5 – 9 m² after laps
Suitable substratesConcrete slabs, cement screeds, precast concrete, existing sound bitumen membranes
Typical reinforcement (this class)Non-woven polyester carrier
Typical underside (this class)Thin polyethylene burn-off film
Selling unitPer roll

Rows marked "this class" are typical for 4.5 kg mineral APP membranes. Always confirm the exact values on the roll label or the manufacturer's data sheet.

Key Features & Benefits

✓
Heavy 4.5 kg/m² build – a thick, robust layer for long-lasting roof protection.
✓
Mineral granule finish – protects the bitumen from UV and heat, so no extra coating is needed on exposed roofs.
✓
APP modified bitumen – good heat resistance, well suited to hot, sunny climates.
✓
Torch-on bonding – fuses fully to the primed slab and to itself at the laps for a continuous waterproof sheet.
✓
Handy 1m x 10m rolls – easy to plan quantities and quick to lay on large flat areas.
✓
Handles ponding water – suitable for flat roofs where water may sit after heavy rain.
✓
Works with what we stock – pair with our bitumen primer, gutters and downpipes for a complete roof drainage and waterproofing job.

Where to Use Bitumax APP Membrane

✓
Flat concrete roofs on houses, apartments, schools, churches and commercial buildings
✓
Roof terraces, balconies and open decks
✓
Concrete gutters, parapet walls and upstands
✓
Podium slabs and car-park decks (with suitable protection layer)
✓
Re-roofing and repair over old, sound bitumen membranes
✓
Water tank bases, canopies and concrete slabs exposed to rain

How to Apply Bitumax APP Membrane

Safety first: torch-on work uses an open flame. Application should be done by a trained waterproofing applicator, with a fire extinguisher on site, gloves, boots and eye protection. Never torch near open gas cylinders, timber or other flammable materials.

Tools & materials you will need

✓
Bitumax APP membrane rolls
✓
Bitumen primer and a roller or brush
✓
Gas torch, hose, regulator and LPG cylinder
✓
Utility knife, tape measure, chalk line and a heated round-nose trowel
✓
Fire extinguisher and personal protective equipment

Step-by-step application

1
Inspect the slab
The surface must be sound, dry, smooth and laid to fall so water drains to the outlets. Check that no rain is expected during application.
2
Clean and repair
Remove dust, loose particles, oil and sharp edges. Fill cracks and hollows with repair mortar and allow to cure.
3
Form fillets at upstands
Make a 45° cement fillet where the slab meets parapet walls so the membrane turns up smoothly without sharp folds.
4
Prime the surface
Apply bitumen primer evenly with a roller or brush. Let it dry completely (touch-dry, no longer sticky) before torching. Follow the primer label for coverage and drying time.
5
Lay out and align
Start at the lowest point of the roof, near the outlet. Unroll the membrane dry, mineral side up, align it with a chalk line, then roll it back up from both ends.
6
Torch and unroll
Heat the underside of the roll and the primed surface evenly until the burn-off film melts and the bitumen turns glossy. Unroll slowly while pressing the membrane down so it bonds fully with no air pockets.
7
Make the laps
Overlap side joints by at least 100 mm and end joints by at least 150 mm. Stagger the end laps of neighbouring rolls. Where a lap falls on the mineral surface, heat and press the granules into the bitumen before laying the next sheet.
8
Seal the joints
Press every lap with a heated round-nose trowel until a small bead of bitumen shows along the edge – this confirms a fully fused, watertight seam.
9
Finish upstands and outlets
Turn the membrane up parapet walls at least 150 mm above the finished roof, fix the top edge into a chase or under a termination bar and seal. Dress the membrane neatly into drainage outlets.
10
Final inspection
Walk the roof and check all laps with a trowel. Re-heat and seal any loose edge. Where possible, carry out a flood test before handing over.
Do not overheat: too much flame burns the bitumen and damages the reinforcement. Heat just enough for the bitumen to flow.

How Many Rolls Do I Need?

Each 1m x 10m roll covers about 8.5 – 9 m² once laps are allowed for. A quick way to estimate:

Rolls needed ≈ (Roof area in m² + upstand area in m²) ÷ 8.5, then round up and add one spare roll for cutting and wastage.

Example: a 100 m² flat roof with 12 m² of parapet upstands → (100 + 12) ÷ 8.5 = 13.2 → 14 rolls, plus 1 spare.

Send us your roof measurements on WhatsApp and our team will help you work out rolls and primer.

Storage & Handling

✓
Store rolls upright on a flat, dry surface – never lay them flat or stack them.
✓
Keep in the shade, away from direct sun, heat and open flames.
✓
Protect from rain and moisture until use.
✓
Handle with care – each roll weighs about 45 kg; lift with two people where needed.

Complete Your Waterproofing Job

Also available at Shabbiri Hardware:

✓
Bitumen primer for torch-on membranes
✓
Kenflex APP roofing membranes
✓
Sika and Asmaco waterproofing and construction chemicals
✓
PVC gutter systems, downpipes, elbows and clips
✓
Cement, mabati and general building materials
Supply only: Shabbiri Hardware does not do installation, but we can share contacts of independent waterproofing applicators near you.

Frequently Asked Questions

How many square metres does one Bitumax 1m x 10m roll cover?

One roll is 10 m² gross. After 100 mm side laps and 150 mm end laps, plan on roughly 8.5 to 9 m² of finished coverage per roll, plus a little extra for upstands and wastage.

What does 4.5 kg mean on the Bitumax membrane?

It is the weight per square metre: 4.5 kg/m². A full 10 m² roll therefore weighs about 45 kg.

Do I need primer before laying Bitumax APP membrane?

Yes. Concrete and screed surfaces should be primed with bitumen primer and allowed to dry fully before torching. We stock bitumen primer at both branches.

Can the mineral-surfaced membrane be left exposed to the sun?

Yes. The mineral granule top surface protects the bitumen from UV, so it can be the exposed top layer on flat roofs and terraces.

Does Shabbiri Hardware install the membrane?

We are supply-only and do not install, but we can share contacts of independent waterproofing applicators.

Where can I buy Bitumax APP membrane in Nairobi?

At Shabbiri Hardware on Magadi Road – Ongata Rongai branch (opposite Hashi Petrol Station) and Tuala branch (past Nazarene University). Call 0741 042484 or WhatsApp 0745 554008.

Do you deliver?

Yes, delivery is arranged according to your location – boda delivery where reachable and courier for upcountry orders. Delivery is charged.

Visit Our Branches – Magadi Road, Nairobi

Ongata Rongai Branch

Magadi Road, opposite Hashi Petrol Station, Ongata Rongai

Get Directions to Rongai Branch

Tuala Branch

Magadi Road, past Nazarene University, Tuala

Get Directions to Tuala Branch

Order Bitumax APP Membrane Today

📞 Call: 0741 042484

💬 WhatsApp: 0745 554008

✉️ Email: shabbirihardware@gmail.com

🌐 Website: www.shabbirihardware.co.ke

🏬 Shabbiri Hardware Kenya Limited – serving builders since 1990

Get a Quote on WhatsApp Call Us Now
APP membrane Kenya Torch-on waterproofing Nairobi Bitumax membrane Mineral roofing felt Flat roof waterproofing Waterproofing Ongata Rongai
KSH 5,000/ piece
In stock
Delivery on request — same-day within Nairobi, next-day countrywide.
Free pickupat Rongai & Tuala branches.
Qty
1
📲 Order on WhatsApp
100% genuine, sourced materials
Secure M-Pesa & card payment
Countrywide delivery arranged
100% Genuine
No fakes, ever
Quality assured
Trusted brands only
Countrywide delivery
Arranged on request
Expert advice
Sales team on WhatsApp

Specifications

CategoryWaterproofing & Sealants
AvailabilityIn stock
Sourced byShabbiri Hardware Kenya Limited

Customer reviews

No reviews yet — be the first to review this product.

Frequently bought together

Customers who bought this often add these to their order.