
SBR Latex Emulsion SBR 161
SBR Latex Emulsion – SBR 161 (10 kg)
A polymer-fortified styrene-butadiene rubber (SBR) emulsion that you add to cement slurries, mortars, renders and screeds. It makes them stick better, bend without cracking and keep water out — the go-to bonding agent and cement admixture for repairs and waterproofing work in Kenya.
What is SBR 161?
SBR 161 is a milky-white synthetic rubber latex supplied in a 10 kg tin. On its own it does nothing — its job is to upgrade the cement mixes you already use. Mixed into the gauging water, the latex particles form a flexible film inside the hardened cement, sealing pores and gripping the surface underneath.
Fundis, contractors and homeowners use it whenever new plaster, screed or concrete must bond firmly to an old surface, or when a render must hold back water in bathrooms, water tanks, basements and balconies.
Technical Specifications
| Product name | SBR Latex Emulsion SBR 161 (polymer fortified) |
|---|---|
| Brand | Zahabiya |
| Chemical base | Styrene-butadiene rubber (SBR) latex emulsion |
| Appearance | Milky white liquid |
| Pack size | 10 kg tin |
| Grade | Construction grade |
| Mixes with | Ordinary Portland cement and sand mixes |
| Application | Brush, broom, trowel or as gauging liquid in the mixer |
| Use area | Interior and exterior; wet and dry areas |
| Storage | Cool, shaded place; keep tightly closed; protect from freezing and direct sun |
Key Benefits
💪 Strong bonding
New mortar grips old concrete, block and plaster — no hollow patches or delamination.
💧 Water resistance
Reduces water absorption, making renders and screeds suitable for wet areas.
🧱 Less cracking
Added flexibility and reduced shrinkage help stop hairline cracks.
🛡️ Tougher surfaces
Improves wear and abrasion resistance and cuts surface dusting on floors.
⚗️ Chemical resistance
Better resistance to mild chemicals, salts and oils than plain cement mixes.
🌍 Easy & safe
Water-based and ready to use — just dilute and mix. No solvents.
Where to Use It
- Bonding slurry / primer before plastering, screeding or patching onto old concrete
- Waterproof renders for bathrooms, kitchens, toilets and shower areas
- Water tanks, septic tanks, manholes, swimming pool surrounds and basements
- Concrete repair mortars — spalled edges, columns, beams and stair nosings
- Floor screeds and toppings that need to resist wear and dust
- Flat roofs, balconies and terraces under tiles
- Improving adhesion of cement-based tile beds on walls and floors
- Thin patching layers that plain mortar would crack or lose bond on
Typical Mixing Guide
Bonding slurry
1 SBR : 1 waterMix the diluted liquid with cement to a creamy slurry and brush it onto the prepared surface.
Waterproof render
1 SBR : 3 waterUse as the gauging liquid for a 1 cement : 3 sand mortar.
Repair mortar
1 SBR : 2–3 waterGauge a 1 cement : 2–3 sharp sand mortar; build up in layers on deep repairs.
Floor screed
1 SBR : 4 waterGauge a 1 cement : 3–4 sand screed for a tougher, low-dust floor.
These are typical SBR ratios. Always confirm against the instructions printed on the tin, and do a small trial for critical work.
How to Apply
- Prepare the surface. Remove dust, oil, loose plaster and old paint. Hack smooth concrete for a good key.
- Dampen the surface. Wet it thoroughly, then let any standing water disappear.
- Dilute the latex. Mix SBR 161 with clean water at the ratio for your job.
- Apply the bonding slurry. Brush or broom the slurry well into the surface.
- Work wet-on-wet. Lay the plaster, screed or mortar while the slurry is still tacky — never let it dry first.
- Mix the main mortar. Use the diluted latex in place of plain water; mix only what you can use within about 30 minutes.
- Cure properly. Protect from sun, wind and rain and keep damp for 1–3 days.
- Clean tools. Wash tools with water straight away — dried latex is hard to remove.
Precautions
- Do not let the bonding slurry dry before placing the next layer — this causes poor bond
- Do not over-mix in the mixer; excess mixing traps air
- Avoid application in heavy rain or very hot direct sun
- Wear gloves and eye protection; wash skin with soap and water after contact
- Keep out of reach of children; do not pour undiluted latex into drains
Why Buy from Shabbiri Hardware?
Since 1990
Over three decades supplying genuine building materials in Nairobi.
Full waterproofing range
Sika, Asmaco, Akfix and more — get the latex, cement additives and sealants in one stop.
Delivery or pickup
Same-day delivery within Nairobi on request, or collect from Rongai or Tuala.
Fundi contacts
We supply only, and can connect you with independent installers.
Frequently Asked Questions
Is SBR 161 a waterproofing coating on its own?
No. It is an additive. Mix it into cement slurry, render or screed to make that mix bond better and resist water.
Can I use it on old plaster or concrete?
Yes — that is its main use. Clean and dampen the old surface, apply SBR bonding slurry, then plaster wet-on-wet.
How much water do I add?
It depends on the job: about 1:1 for bonding slurry and 1:3 to 1:4 for renders and screeds. Check the tin for the exact ratio.
Can it be used in water tanks?
Yes, SBR-modified renders are widely used to line concrete and block water tanks. Allow full curing before filling.
Do you deliver outside Nairobi?
Yes, next-day countrywide delivery can be arranged on request.
Visit Our Branches
Need SBR 161 for your project?
Tell us the quantity and location — we'll confirm stock and delivery.
Chat on WhatsAppSpecifications
| Model | SBR-161 |
| Category | Waterproofing & Sealants |
| Availability | In stock |
| Sourced by | Shabbiri Hardware Kenya Limited |
Customer reviews
No reviews yet — be the first to review this product.
Frequently bought together
Customers who bought this often add these to their order.



