
Self Drilling Screws Truss Head 1 Inch (25mm) – Zinc Plated Wafer Head Tek Screws, 500pcs Packet
Self Drilling Screws Truss Head 1" (25mm) – 500pcs Packet
Zinc plated truss (wafer) head tek screws that drill, tap and fasten in one step. The go-to screw for metal stud partitions, gypsum ceilings and light gauge steel work across Nairobi and Kenya.
Product Overview
The 1 inch truss head self drilling screw (SDS) has a built-in drill tip that cuts its own hole in steel, then forms its own thread as you drive it. There is no need to drill a pilot hole first, so fixing goes faster and holes line up perfectly.
Its wide, flat, low-profile truss head spreads load over a bigger area and sits almost flush with the surface. That is exactly why fundis use it to join metal studs to tracks in gypsum partitions — the head does not bulge under the board, so gypsum lies flat and finishes cleanly.
Packed 500 pieces per packet, ideal for contractors, drywall installers, fabricators and DIY projects. Available at Shabbiri Hardware, Magadi Road – Ongata Rongai and Tuala branches.
Technical Specifications
| Product | Self Drilling Screw (SDS / Tek Screw), Truss Head |
|---|---|
| Length | 1 inch (approx. 25 mm) |
| Head type | Truss / wafer head – wide, flat, low profile |
| Drive type | Phillips cross recess (PH2 bit) |
| Point type | Self drilling drill point (tek point) |
| Material | Hardened carbon steel |
| Finish | Zinc plated (silver / bright) for corrosion resistance indoors |
| Thread | Fine machine-type thread for steel |
| Suitable base materials | Light gauge steel, metal studs & tracks, sheet metal, aluminium, galvanised steel |
| Recommended tool | Electric drill / screwdriver with clutch, PH2 bit |
| Packing | 500 pieces per packet |
| Best environment | Indoor and sheltered areas |
Diameter and drilling capacity vary by manufacturer batch — please check the packet or ask our branch team to confirm the gauge for your steel thickness.
Key Features & Benefits
Common Applications
- Joining metal studs to floor and ceiling tracks in gypsum partitions
- Fixing gypsum ceiling furring channels and main channels together
- Light gauge steel framing and steel-to-steel connections
- Fixing sheet metal, flashing trims and metal brackets
- Ducting, cable trays and electrical boxes
- Aluminium frames, shopfitting and display units
- General fabrication, workshop and DIY projects
How to Use
- Choose the right length. The 1" screw suits joining two thin metal layers such as stud and track. The drill tip should fully pass through the steel before the threads engage.
- Fit a PH2 bit. Use a cordless drill or screwdriver with a clutch. A magnetic bit holder keeps the screw steady.
- Mark and clamp. Mark your fixing points and hold the metal parts tightly together so no gap forms between layers.
- Start straight. Hold the screw at 90° to the surface. Apply firm, steady pressure and run the drill at medium speed — let the drill point do the cutting.
- Drive home. Once the tip breaks through, the threads pull the screw in. Stop as soon as the head sits flat against the surface.
- Do not over-tighten. Over-driving strips the thread in thin steel. Set the clutch low and increase only if needed.
- Check and continue. Confirm each screw is firm, then continue along the stud or channel at your planned spacing.
Important Tips & Safety
Frequently Asked Questions
What are truss head self drilling screws used for?
They fix metal to metal without pre-drilling — mainly metal studs to tracks in gypsum partitions, ceiling channels, light steel framing, sheet metal, ducting and electrical boxes.
Can I use these screws for mabati roofing?
Not recommended. They have no sealing washer, so water can get in. Use hex head roofing screws with an EPDM washer for iron sheets.
Do I need to drill a hole first?
No. The drill point cuts its own hole in thin steel. Simply drive the screw with a drill and PH2 bit.
How many screws are in one packet?
Each packet has 500 pieces.
Do you deliver?
Yes, delivery is available on request within Nairobi and countrywide, plus free pickup at our Rongai and Tuala branches.
Where can I buy self drilling screws near me in Nairobi?
Visit Shabbiri Hardware on Magadi Road — Ongata Rongai branch (opposite Hashi Petrol Station) or Tuala branch (past Nazarene University).
Visit Our Branches
Contact Shabbiri Hardware
Specifications
| Model | TRUSS HEAD 1" |
| Category | Screws |
| Availability | In stock |
| Sourced by | Shabbiri Hardware Kenya Limited |
Customer reviews
No reviews yet — be the first to review this product.
Frequently bought together
Customers who bought this often add these to their order.



