Loading branch status…
Home / Waterproofing & Sealants / WATER BAR - FLAT
WATER BAR - FLAT

WATER BAR - FLAT

KSH 1,100/ roll
In stock
About this product
Waterproofing & Sealants

Flat Water Bar (Waterstop) – Stops Water Leaking Through Concrete Joints

Whenever concrete is cast in more than one pour — a slab, then a wall on top; or one section of a basement wall, then the next — a joint is left between the two pours. Water finds that joint and seeps through it. A Flat Water Bar is a flexible strip cast half into the first pour and half into the second, so it sits across the joint like a hidden barrier and blocks the water's path.

It is the simple, low-cost way to keep basements, water tanks, retaining walls, foundations, swimming pools and septic tanks dry for the life of the building.

💧 Blocks water at joints 🧱 Cast into the concrete 🔁 Flexible & long-lasting 📍 Rongai & Tuala stock

📋Specification

ProductFlat Type Water Bar (Waterstop)
MaterialFlexible PVC / rubber compound
ProfileFlat strip with raised ribs along its length (ribs grip the concrete and lengthen the water path)
ColourBlue
Joint typeConstruction joints (cold joints) in concrete
PlacementCast-in (internal) – centred across the joint, half in each pour
Width / thicknessAsk our team for the sizes currently in stock (common widths range from 150 mm to 250 mm)
Jointing methodHeat-welded or overlapped and tied, depending on the job
ResistanceWater, soil moisture, alkalis in concrete; does not rot or rust
Sold byKSh 1,100 per unit as listed above

⭐Key Features

Ribbed gripRaised ribs lock firmly into the concrete so the bar can't be pushed out by water pressure.
FlexibleBends around corners and follows minor movement of the concrete without cracking.
Rot & rust proofUnlike steel strips, it never corrodes and is not attacked by soil or concrete chemicals.
WeldableLengths can be heat-joined into one continuous barrier with no weak gaps.
LightweightEasy to carry, cut with a knife and fix to the steel reinforcement on site.
PermanentOnce cast in, it works for the whole life of the structure — no maintenance.

📐Coverage Area – How Much Do I Need?

A water bar is measured by the length of joint it protects, not by square metres. Simply measure every joint where one concrete pour meets another, add them up, and add about 10% extra for overlaps, corners and cutting.

Example 1 – Basement / water tank (4 m × 3 m): joint between floor slab and walls = 4+3+4+3 = 14 m. Add 10% ≈ 15.5 m of water bar.

Example 2 – Retaining wall 20 m long, cast in 2 lifts: horizontal joint 20 m + 10% ≈ 22 m of water bar.

Tip: also count any vertical joints where you stop and restart a wall pour.

Not sure? Send us your plan or wall/tank sizes on WhatsApp and we'll calculate the quantity for you — free.

Benefits

  • Keeps basements, tanks and foundations dry
  • Prevents damp, mould and peeling paint on walls
  • Stops water from rusting the steel reinforcement
  • Far cheaper than repairing a leaking joint later
  • Water tanks hold water without loss
  • Protects the long-term strength and value of the building

🏗️Where It Is Used

BasementsFloor-to-wall and wall-to-wall joints below ground.
Water tanks & reservoirsUnderground and elevated concrete tanks.
Swimming poolsPool floor and wall pour joints.
Retaining wallsWalls holding back wet soil.
Septic & sewage tanksKeeps waste in and groundwater out.
Foundations & culvertsFootings, lift pits, channels and drains.

🛠️How to Install

  1. Mark the joint line. Decide exactly where the first pour will stop (e.g. the top of the floor slab where the wall will start).
  2. Position the bar centrally. Place the water bar so that half its width goes into the first pour and half sticks out to go into the next pour. Keep it straight and level.
  3. Fix it to the steel. Tie the edges of the bar to the reinforcement bars with binding wire every 250–300 mm so it can't fold or move when concrete is poured. Tie only through the outer edge — never punch holes in the middle of the bar.
  4. Join the lengths. Heat-weld lengths end-to-end for a continuous seal, or overlap generously and tie tightly. Make sure there are no gaps, especially at corners.
  5. Pour the first concrete. Pour and vibrate carefully around the bar so concrete fills both sides with no air pockets. Don't let the vibrator poker hit the bar directly.
  6. Protect the exposed half. Keep the sticking-out half clean, straight and undamaged until the next pour.
  7. Pour the second concrete. Clean the joint surface, then pour the next section around the exposed half and vibrate well. The bar is now locked inside the joint.
Important: We are a supply-only shop. For large or critical structures (deep basements, big reservoirs), use a qualified contractor — ask us and we'll share contacts of independent installers.

✅How to Use – Dos & Don'ts

  1. Plan it before casting. A water bar must be placed before concrete is poured — it cannot be added to an already-leaking joint.
  2. Use it at every joint below water level. One missed joint is enough for water to get in.
  3. Store it out of direct sun and keep it clean of oil, mud and grease before use so concrete bonds well.
  4. Combine for best results. For full protection, pair the water bar with a surface waterproofing coating or membrane — ask us for Sika options in stock.
  5. Flat type = construction joints. For joints designed to move (expansion joints), ask for a centre-bulb water bar instead.

❓Frequently Asked Questions

What is a water bar used for?

It seals the joint between two concrete pours so water cannot leak through — mainly in basements, water tanks, pools and retaining walls.

Can I fix a leaking joint with a water bar?

No. It is cast into the concrete during construction. For an existing leak, ask us about injection or surface waterproofing products.

How do I know how many metres to buy?

Add up the length of all joints and add about 10%. Send us your sizes on WhatsApp and we'll calculate it for you.

Do you deliver?

Yes — same-day delivery within Nairobi and next-day countrywide on request, or free pickup at our Rongai and Tuala branches.

📍Visit Our Branches

Shabbiri Hardware – Ongata RongaiMagadi Road, opposite Hashi Petrol Station
Shabbiri Hardware – TualaMagadi Road, past Nazarene University

Need Water Bar for Your Site?

Tell us your joint length and we'll quote and arrange delivery the same day.

💬 Order on WhatsApp 📞 Call 0741 042 484
M-Pesa Paybill 542 542 · Account 78653 · ✉️ shabbirihardware@gmail.com
KSH 1,100/ roll
In stock
Delivery on request — same-day within Nairobi, next-day countrywide.
Free pickupat Rongai & Tuala branches.
Qty
1
📲 Order on WhatsApp
100% genuine, sourced materials
Secure M-Pesa & card payment
Countrywide delivery arranged
100% Genuine
No fakes, ever
Quality assured
Trusted brands only
Countrywide delivery
Arranged on request
Expert advice
Sales team on WhatsApp

Specifications

CategoryWaterproofing & Sealants
AvailabilityIn stock
Sourced byShabbiri Hardware Kenya Limited

Customer reviews

No reviews yet — be the first to review this product.

Frequently bought together

Customers who bought this often add these to their order.