Sika Grout 217 Engineering Grout 25kg – High Performance Non-Shrink Grout in Nairobi, Kenya
Sika Grout 217 Engineering Grout 25kg – High Performance Non-Shrink Grout in Nairobi, Kenya
SikaGrout®-217 is a ready to use, shrinkage compensated cementitious grout. Add water, mix, and pour a grey fluid mortar that fills base plates, machine beds and anchor bolt pockets completely and builds high early strength for quick commissioning.
Product Overview
SikaGrout-217 is an engineering grout made by Sika for precision grouting and gap filling where full contact and load transfer matter. It comes as a pre-blended grey powder containing cement, graded aggregates and additives. Once mixed with the correct amount of clean water, it turns into a free-flowing mortar that runs under base plates and into tight spaces without vibration.
Because the grout is shrinkage compensated, it does not pull away from steel or concrete as it hardens. It develops high compressive and flexural strength from the first day, so machines, columns and equipment can be put to work sooner. It also has good resistance to internal frost damage and chipping.
At Shabbiri Hardware we supply SikaGrout-217 in 25 kg bags only, from both our Ongata Rongai and Tuala branches on Magadi Road. Contractors, engineers, fundis and factory maintenance teams across Nairobi, Kajiado, Kitengela and Ngong rely on us for genuine Sika construction chemicals.
Technical Specifications Sika Kenya data
| Property | Value |
|---|---|
| Product name | SikaGrout®-217 |
| Brand | Sika |
| Product type | High performance, shrinkage compensated cementitious grout (engineering grout) |
| Pack size | 25 kg bag |
| Appearance and colour | Grey powder, mixes to a grey fluid mortar |
| Maximum grain size | 2.36 mm |
| Fresh mortar density | Approx. 2.00 kg per litre |
| Mixing water | 3.25 to 3.50 litres per 25 kg bag |
| Pot life | Approx. 30 minutes |
| Application temperature | Between +5 °C and +35 °C ambient |
| Approximate yield | About 14 litres of grout per 25 kg bag |
| Storage | Original sealed bags, dry place, away from direct sunlight |
Compressive Strength
Values are laboratory figures from the Sika Kenya product data sheet. Site results vary with water content, temperature, mixing and curing. Yield is an estimate based on fresh density.
Key Features and Benefits
Non-shrink performance
Shrinkage compensation keeps full contact under base plates, so loads transfer evenly.
High early strength
Reaches useful strength within a day, allowing faster machine commissioning and less downtime.
Excellent flow
Fluid consistency flows into narrow gaps and around bolts without vibration or rodding.
Ready to use
Pre-blended on site with water only. No sand or cement to measure, so every batch is consistent.
Durable
Good resistance to internal frost damage and chipping for long-term service.
High flexural strength
Handles vibration and dynamic loads from pumps, motors, generators and crushers.
Where to Use Sika Grout 217
Machine bases
Bedding and levelling of pumps, compressors, generators, motors and production machinery.
Steel base plates
Grouting under steel column base plates in warehouses, factories and mezzanines.
Anchor bolts
Fixing holding-down bolts, rails, posts and anchors into concrete pockets.
Precast elements
Filling joints and connections between precast concrete beams, columns and panels.
Bridge bearings
Bedding of bearings and seatings on civil engineering structures.
Gap and void filling
Filling cavities, recesses and openings in concrete where a strong, non-shrink fill is needed.
How to Use Sika Grout 217 – Step by Step
Prepare the concrete surface
The base concrete must be sound, clean and free from oil, grease, dust, laitance and loose particles. Roughen smooth surfaces by chipping or scabbling to give a good key.
Pre-soak the surface
Saturate the concrete with clean water for several hours before grouting, ideally overnight. Remove all standing water just before pouring so the surface is damp but with no puddles.
Clean steel and bolts
Base plates, bolts and steel surfaces in contact with the grout should be free from rust scale, oil and dirt.
Fix the formwork
Build strong, watertight formwork around the area, a little higher than the underside of the base plate. Seal joints so the fluid grout cannot leak out. Leave a pouring side with a head box for pressure.
Measure the water
Pour 3.25 to 3.50 litres of clean water per 25 kg bag into a clean mixing drum. Never exceed this amount, as extra water reduces strength and causes bleeding and cracks.
Mix thoroughly
Add the full bag of powder gradually while mixing with a low-speed drill and paddle. Mix for about 3 to 5 minutes until the grout is smooth, lump free and fluid. Mix full bags only for a consistent result.
Pour continuously
Pour from one side only, so air is pushed out ahead of the grout and not trapped under the plate. Keep a steady head of grout and pour without stopping until the space is full.
Work within the pot life
Place the mixed grout within about 30 minutes. Do not re-temper grout that has started to stiffen by adding more water.
Cure properly
Protect exposed grout from sun, wind and rapid drying. Keep it moist with wet hessian or polythene sheeting, or apply a curing compound, for at least 3 days.
Clean tools
Wash mixers and tools with water immediately after use. Hardened grout can only be removed mechanically.
Work within +5 °C to +35 °C. In hot weather, use cool mixing water and keep bags in the shade. In cold early mornings, wait until temperatures rise.
Packaging, Storage and Safety
Packaging
Available only in 25 kg bags. Plan quantities using the yield of about 14 litres of grout per bag.
Storage
Keep in unopened original bags, off the ground, in a dry and covered place, away from direct sunlight and moisture.
Safety
Contains cement, which is alkaline. Wear gloves, goggles and a dust mask. Avoid contact with skin and eyes and rinse with clean water if contact occurs.
Why Buy Sika Grout 217 from Shabbiri Hardware
- Trusted hardware and building materials supplier in Nairobi since 1990.
- Genuine Sika construction chemicals, stored correctly in dry conditions.
- Two convenient branches on Magadi Road serving Ongata Rongai, Tuala, Kiserian, Ngong, Kitengela, Karen and Nairobi.
- Full range of Sika, Asmaco and Akfix products for repairs, waterproofing, anchoring and grouting.
- Bulk orders welcome for contractors, factories and site projects.
Frequently Asked Questions
What pack size does Sika Grout 217 come in?
SikaGrout-217 is available only in 25 kg bags.
How much water do I mix with one bag?
Use 3.25 to 3.50 litres of clean water per 25 kg bag. Adding more water weakens the grout and can cause bleeding and cracking.
How long can I work with it after mixing?
The pot life is about 30 minutes, so mix only what you can pour in that time.
Is Sika Grout 217 a non-shrink grout?
Yes. It is shrinkage compensated, which helps it keep full contact under base plates and equipment.
How many bags do I need?
Each 25 kg bag gives about 14 litres of grout. Work out the volume of the gap in litres (length x width x depth in decimetres) and divide by 14, then add a little extra for wastage.
Can I use it for tile grouting?
No. SikaGrout-217 is an engineering grout for structural and machine grouting. For tile joints, ask our team for a suitable tile grout.
Related Searches
Visit or Contact Shabbiri Hardware
Call us, email or visit either branch to order Sika Grout 217 in 25 kg bags.
Ongata Rongai Branch
Magadi Road, opposite Hashi Petrol Station, Ongata Rongai
Tuala Branch
Magadi Road, past Nazarene University, Tuala
Email and Website
Ongata Rongai Branch Map
Tuala Branch Map
Specifications
| Brand | Sika |
| Model | G-217 |
| Category | Cement |
| Availability | In stock |
| Sourced by | Shabbiri Hardware Kenya Limited |
Customer reviews
No reviews yet — be the first to review this product.
Frequently bought together
Customers who bought this often add these to their order.
